Doug Posted December 15, 2020 Share Posted December 15, 2020 BuzzTV Support, I have had my new BuzzTV VidStick Plus for one week, and have encountered two frustrating problems and one unexplained issue. I have used both the IR sensor cable and the Bluetooth connection methods for my BT-100 remote; but keep having to either unplug & then plug-in the power adapter or wiggle the microUSB connector to get the VidStick to start-up using the remote. This happens if I use the stand-by method or Power Off method to shut down the VidStick device. In addition to VidStick start-up issue, I have encounter three total lockups (device would not respond to any key inputs from the remote) of the VidStick. To work around the lockup condition I had to cycle the power adapter or remove & reinstall the BT-100 batteries. It’s a real pain not knowing if the VidStick is going to power up each time I want to use it. The unexplained issue deals with using a USB 3.0 USB Ethernet adapter with the VidStick Plus. I have a Ugreen 3.0 USB Gigabit Ethernet adapter (model 20256) that I used with my VidStick. The issue deals with the reported MAC addresses: Label on back of VidStick reads: MAC Address – d0:76:79:e0:02:15 (see attached pic) Wireless connection MAC address reported by BuzzTV 4 software & my Netgear router: 44:01:bb:76:b0:6a Ethernet connection MAC address reported by my Netgear router: 00:0e:c6:55:f0:bb Ethernet connection MAC address reported by BuzzTV 4 software: fe80:7545:dd4:9487:60c0 (see attached pic) I’m not sure what’s happening with MAC address printed on the VIdStick Plus label as compared to the reported results I encountered using both the wireless and ethernet connections. The ethernet connection seems work OK; however the internet speed received is much less then my usual 220mb download speed. I’m looking for answers and really need a permanent fix for my VidStick Plus startup and lock-up problems Thanking you in advance for time and cooperation with my BuzzTV hardware problems. Doug Quote Link to comment Share on other sites More sharing options...
nbs. Posted December 15, 2020 Share Posted December 15, 2020 (edited) Buzz have stated that they only support their usb adapter with drivers so that could be your main issue the mac addy on stick will match device id in server settings the new software coming out will be reduced to one id line Edited December 15, 2020 by nbs. Quote Link to comment Share on other sites More sharing options...
Doug Posted December 15, 2020 Author Share Posted December 15, 2020 I used the Vidstick Plus 99% of time with a wireless internet connection, and I'm still getting the startup problems using the remote in either the IR or Bluetooh connection method. It's the VidStick start-up problem I need to solve. I'll see about purchasing the Ethernet adapter that is offered by BuzzTV. Quote Link to comment Share on other sites More sharing options...
Doug Posted December 15, 2020 Author Share Posted December 15, 2020 It appears the inability to get the VidStick Plus to wake-up using the remote was addressed in this forum back on June 18th by bad8511. After reading the replies to that post there are several VidStick owners with the same problem as I am experiencing, but with no real solution being posted. Does anyone know if the soon to be release BuzzTV 5 software will be available for the VidStick Plus, and will that new software release address this issue along with many other bug fixes? Quote Link to comment Share on other sites More sharing options...
dishuser Posted December 15, 2020 Share Posted December 15, 2020 there's a buzztv 4 update pending that should fix issues Quote Link to comment Share on other sites More sharing options...
allaboutbuzz Posted December 15, 2020 Share Posted December 15, 2020 49 minutes ago, Doug said: It appears the inability to get the VidStick Plus to wake-up using the remote was addressed in this forum back on June 18th by bad8511. After reading the replies to that post there are several VidStick owners with the same problem as I am experiencing, but with no real solution being posted. Does anyone know if the soon to be release BuzzTV 5 software will be available for the VidStick Plus, and will that new software release address this issue along with many other bug fixes? This is an issue we plan to address in the next update for the VidStick's The 4000s update is paused, but will resume this week Then the 4500s update will roll out, followed by the Vidstick's and E1. So expect the update soon. As for your Ethernet Adapter issue, it is advised to use the one being sold for Buzz TV It has already been discussed on this forum though, that you won't get full 1GB speeds over USB as this just isn't possible over USB. Quote Link to comment Share on other sites More sharing options...
allaboutbuzz Posted December 15, 2020 Share Posted December 15, 2020 51 minutes ago, Doug said: It appears the inability to get the VidStick Plus to wake-up using the remote was addressed in this forum back on June 18th by bad8511. After reading the replies to that post there are several VidStick owners with the same problem as I am experiencing, but with no real solution being posted. Does anyone know if the soon to be release BuzzTV 5 software will be available for the VidStick Plus, and will that new software release address this issue along with many other bug fixes? And yes the Buzz 5 update is planned for all Buzz models using Buzz 4 So XR + XRS 4000 XR + XRS 4500 XRS 4500 MAX E1 VidStick, VidStick+, VidStick MAX XRS 4900 We have a pending release for approximately February 1st, 2021 Quote Link to comment Share on other sites More sharing options...
Doug Posted December 15, 2020 Author Share Posted December 15, 2020 Thanks AllAboutBuzz & dishuser for the quick and informative replys to my VidStick Plus software issues. Quote Link to comment Share on other sites More sharing options...
aobabs Posted February 19, 2021 Share Posted February 19, 2021 I have the same problem my remote is stuck most of the time and the remote won't turn my vidstick+ on. I have to keep unplugging it and plugging it back in to the power outlet to start it. It's really frustrating and am disappointed in this product . The problem started when I dud the recent update.is there a fix to this problem. aobabs.. Quote Link to comment Share on other sites More sharing options...
nbs. Posted February 19, 2021 Share Posted February 19, 2021 Do a hard reset Quote Link to comment Share on other sites More sharing options...
aobabs Posted February 20, 2021 Share Posted February 20, 2021 I did hard reset several times and it did not solve the problem Quote Link to comment Share on other sites More sharing options...
nbs. Posted February 20, 2021 Share Posted February 20, 2021 (edited) did you email buzz about the issue? Do you have your ir cable plugged in? Edited February 20, 2021 by nbs. Quote Link to comment Share on other sites More sharing options...
aobabs Posted February 20, 2021 Share Posted February 20, 2021 I emailed buzz never got a reply from them Quote Link to comment Share on other sites More sharing options...
nbs. Posted February 20, 2021 Share Posted February 20, 2021 thats unusual I would try again what about the ir cable? Quote Link to comment Share on other sites More sharing options...
aobabs Posted February 20, 2021 Share Posted February 20, 2021 Connected the IR cable too Quote Link to comment Share on other sites More sharing options...
dishuser Posted February 20, 2021 Share Posted February 20, 2021 2 hours ago, aobabs said: I did hard reset several times and it did not solve the problem did you use a toothpick to do this? Quote Link to comment Share on other sites More sharing options...
aobabs Posted February 20, 2021 Share Posted February 20, 2021 I used a pin 1 Quote Link to comment Share on other sites More sharing options...
nbs. Posted February 20, 2021 Share Posted February 20, 2021 12 hours ago, aobabs said: Connected the IR cable too since the remote is also an ir it should work fine Does it turn unit on and off? does it work ok? Quote Link to comment Share on other sites More sharing options...
allaboutbuzz Posted February 22, 2021 Share Posted February 22, 2021 On 2/19/2021 at 9:18 PM, aobabs said: Connected the IR cable too If you have the IR cable connected And want to use the remote as IR Try turning off Bluetooth You can do so under the Remote and Accessories menu of Android settings Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.